Search found 120 matches
- Thu May 16, 2019 6:22 am
- Forum: Nerian Support Forum
- Topic: Changing the Resolution of the Camera
- Replies: 6
- Views: 32579
Re: Changing the Resolution of the Camera
I received the file. I'm checking the configuration and will get back to you.
- Wed May 15, 2019 12:13 pm
- Forum: Nerian Support Forum
- Topic: Changing the Resolution of the Camera
- Replies: 6
- Views: 32579
Re: Changing the Resolution of the Camera
This seems odd. Can you please email your configuration (can be downloaded from the maintenance page) to service@nerian.com. Also please check that on the status page it says "Model: SceneScan Pro"
- Wed May 15, 2019 11:02 am
- Forum: Nerian Support Forum
- Topic: Changing the Resolution of the Camera
- Replies: 6
- Views: 32579
Re: Changing the Resolution of the Camera
The Pixel Binning configuration is found on the "Cameras" page. You should set binning horizontal and binning vertical both to 1 (you might have to change one after another). This configuration is set for both cameras.
Regards,
Konstantin
Regards,
Konstantin
- Wed May 08, 2019 11:00 am
- Forum: Nerian Support Forum
- Topic: Changing in IP of the Camera
- Replies: 9
- Views: 55544
Re: Changing in IP of the Camera
Hi Eren, you seem to have given your computer the IP address 168.69.69.5, which is the same address which you said you used for SceneScan. You need to give your computer a different address within the same subnet (160.69.69.???). If you can't get it to work, you can use the reset switch on the back ...
- Sun May 05, 2019 6:28 pm
- Forum: Nerian Support Forum
- Topic: Recommended Average Reprojection Error
- Replies: 3
- Views: 28448
Re: Recommended Average Reprojection Error
Hi Aditya, this depends on your camera resolution and lenses. For a 0.5 megapixel resolution and non-wide-angle lenses a value below 0.1 pixels indicates a very good calibration. For higher camera resolutions you must expect a larger error. Also, for wide angle lenses you will get higher errors due ...
- Fri May 03, 2019 11:56 am
- Forum: Nerian Support Forum
- Topic: Non-parallel setup
- Replies: 2
- Views: 11853
Re: Non-parallel setup
Angled camera set-ups are unfortunately not possible. You must mount them in a parallel configuration.
It is possible to get the system to work even with non-synchronizable cameras. But if the cameras or an object in the scene moves during image acquisition, you will receive erroneous results
It is possible to get the system to work even with non-synchronizable cameras. But if the cameras or an object in the scene moves during image acquisition, you will receive erroneous results
- Thu May 02, 2019 3:21 pm
- Forum: Nerian Support Forum
- Topic: SceneScan Pro as active stereo
- Replies: 2
- Views: 11830
Re: SceneScan Pro as active stereo
Yes this works very well. We have made good experiences with structured light projectors by Effilux (their EFFI-Lase projector). Also, consumer video projectors work well. Another option are laser pattern projectors based on diffraction, but they are usually much dimmer than an LED-based projector. ...
- Thu May 02, 2019 1:02 pm
- Forum: Nerian Support Forum
- Topic: Compatible Cameras
- Replies: 2
- Views: 11808
Re: Compatible Cameras
Hi! the cameras must support the USB3 Vision standard. This does not seem to be the case for the linked Ximea cameras. Ximea supports USB3 Vision with their higher-end board-level cameras. For example this one: https://www.ximea.com/en/products/usb-31-gen-1-with-sony-cmos-xic/board-level-cameras-usb...
- Fri Apr 12, 2019 6:46 am
- Forum: Nerian Support Forum
- Topic: Can't detect calibration board
- Replies: 2
- Views: 12379
Re: Can't detect calibration board
Hi Carlos There are a few reasons that could prevent a detection: * Low image contrast * The pattern is outside of the visible range for one camera * At least one circle of the pattern is occluded * The pattern is too far away * The pattern is very unevenly illuminated (e.g. a strong shadow on the p...
- Wed Mar 27, 2019 2:46 pm
- Forum: Nerian Support Forum
- Topic: Welcome to the new Nerian support forum
- Replies: 1
- Views: 9271
Welcome to the new Nerian support forum
Improving support for our growing customer base is one of our top priorities. This is why we have now launched a new support forum. This forum will be the place to ask your questions, which will then be answered directly by our staff. The advantage of using a forum is that you are able to read the q...